Yamaha Rhino Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 32 Results
  1. CVT, Sheaves and Wet Clutch
    Rhino 450. I changed my primary sheave/clutch and now the belt sits too high on the secondary sheave. Any idea on how to fix it? Shim secondary sheave, smaller belt? The widest part of my belt is 1.25" and the widest part of the secondary is only ~1". Thanks for the help on my first post!
  2. General Rhino Discussions
    I bought a 2009 700 best I can tell bone stock with 28x11-12 tires and 2” wheel spacers. Approx 450 hrs/2200ish miles and runs really strong took it on first ride for 3 days at Ride Royal Blue. Lots of mud and some technical trails but the old girl did everything I asked and even out performed...
  3. CVT, Sheaves and Wet Clutch
    Looking for experience with niche clutch housing part #5KM-16611-10-00. I know niche is a bad word when it comes to top end kits but was wondering if anyone has any experience with clutch parts and possibly even primary. My clutch needs attention and started to slug wet clutch but I can’t get...
  4. Engine
    I changed the one way bearing (for the China made. Witch I kno is not suggested) and it ran fine, no noice ,no hesitation. Took it to Uwharrie for a test and it done great but did over heat a little, but as soon as it did I shut it off and let cool. When I returned home it was fine. A couple...
  5. General Rhino Discussions
    Recently i purchased a 2007 Yamaha Rhino 660 i cant afford to give it to a dealer and get charged $1200 plus i would rather do this myself to know how to do it.... when i first got it i noticed brakes were grabbing got brand new pads, rotors and calipers to be safe and it seemed a little better...
  6. CVT, Sheaves and Wet Clutch
    2012 Rhino 700 I had a rhino come in with a speed issue, (would only go 20). We replaced the Clutch ( new plates, new sheaves, new belt etc.) all parts were from yamaha and stock. After the replacement the Rhino would only go 30 then it sounds like it is hitting the rev limiter. We have...
  7. Racing Specific Equipment
    Anyone have comet clutch parts
  8. Racing Specific Equipment
    I'm looking to buy a bronco clutch for my 660 for some desert racing. Let me know if you have one or know of one for sale. Thanks Cameron
  9. CVT, Sheaves and Wet Clutch
    Recently purchased a Calif. street legal Rhino. Just got some 25" DOT Radial tires. Right now top speed is 42-45 mph. Only upgrade is an old Dynatec CDI, stock air cleaner, carb jets?, and exhaust. If I upgrade it a better intake (K&N) and aftermarket exhaust, and a 9000 rpm CDI, what top...
  10. General Rhino Discussions
    I just bought a 07 Rhino and quickly discovered the primary is destroyed. The weights were shredded and the old grease was more like tar. The inside of the Sheave is totally scarred from the destroyed weights. I found a 03 Grizzly 660 primary but am unsure if it will be a match for my 07 Rhino...
  11. CVT, Sheaves and Wet Clutch
    I had a very unfortunate experience with Team industries last week. I want to share my experience with everyone in hopes it can save some one from the same outcome. I had over 12k invested in an awesome Can am Maverick setup. Unfortunatly a team clutch was part of my upgrades and after only 100...
  12. Engine
    First post, but I have been reading many threads on here and it has been helpful. I just purchased my first side by side, and my first Rhino. It is a 2007 660 (carb), completely stock except the wheels and tires. It has 280 hours, 2600 miles. The wheels are: Front 26x9x14 Maxxis Mud Bog R...
  13. General Rhino Discussions
    I keep stripping the primary and cam plate this has happened twice. The second time I was hauling a decent load but the first tine I was empty. It doesn't look like the shaft is bent or hurt in any way. Can anyone help me iut so that when I install the new parts that it doesn't happen again?
  14. Rhino Parts
    i need 150 by Fri. i have a brand spankin new set of 8000K HIDs, stock clutch, stock CDI, stock secondary spring, a green/black soft top (has a tear in the side but was super glued and works fine) and i think i have a few other things ill sell for 150 + shipping. i can also throw in some...
  15. Rhino Parts
    i have a stock 660 CDI, stock clutch, stock secondary spring, 8000k HIDs and i think i have some other parts layin around here too. i also have paint. i have 3 cans or green spray paint and 4 cans of white Krylon. *MUST SELL BY TUESDAY*. shoot me offers. post here, PM or text 910-580-1879
  16. Rhino Parts
    i have a stock full system that is real nice, a machined clutch, 8000K HIDs, and a CDI. need this stuff gone. text 910-580-1879 for prices
  17. Engine
    so at 50mph my motor sounds about like its gonna blow. soon imma be runnin 26 or 27" Zillas. i have stock clutch weights. can i put ODs in my standard UTV Crap machined clutch? i can run 59 with a bad tuned carb right now. more is great and i cant lose any low end. gaining low and mid would be...
  18. Engine
    i have a random backfire every now and then, dunno why. on power, so i was thinkin about a Rotax swap but now after seein the $6K number im like f*** that noise. i have a fully rebuilt motor with a Namura piston. i want more power to get up and move but i dont want to lose any reliability. what...
  19. Engine
    how far can a stock clutch be machined? i allready have a utv crap one. but if this stock one can give me even more umph then why not. also with the mods listed in sig im hittin around 53mph with 2 ppl on it and it gets there pretty dang fast in my opinion. it does need a carb tune. but is it...
  20. Tutorials
    [edit: Sorry about the typo in the title. Mods, can you fix for me? Thanks!] So I was pulling off my clutches because the primary clutch is toast (fins broken in sheave). So thought I'd pull out the wet clutch to inspect while I was in there. I'm stuck because there is no clearance to remove...
1-20 of 32 Results
Top