Yamaha Rhino Forum

Stator or Regulator not working

This is a discussion on Stator or Regulator not working within the How-To forums, part of the General Rhino category; Quote: Originally Posted by erniejoe1 Hello, I just installed an HO stator and thought maybe you could use some pointers. Just an FYI if you ...


Go Back   Yamaha Rhino Forum - Rhino Forums.net > General Rhino > How-To


How-To For Modifications, Bolt-Ons, Maintenance and Troubleshooting How-To's - Pictures make it better!

Reply
 
LinkBack Thread Tools Display Modes
  #16 (permalink)  
Old 11-01-2011, 02:08 PM
Member
 
First Name: Robbie
My Rhino: 2005 / 660 Rhino
Join Date: May 2011
Location: Phoenix
Posts: 18
View rjjencke's Photo Gallery(0)
Quote: Originally Posted by erniejoe1 View Post
Hello,
I just installed an HO stator and thought maybe you could use some pointers.
Just an FYI if you plan on running any accessories you may want to upgrade to an HO stator.
You will need a new gasket, make sure to use the factory gasket do not use the paper one, they don't keep them in stock so I suggest you order one. If you have any kind of motor skills this shouldn't take more then a couple hours.
If your using or have air tools a big plus for removing just make sure you don't overtorque when installing
If you have a sevice manual it starts on page 4-40.
Hope this helps a little.
Yes, thanks Erniejoe1, good to know. How bad is the dealer going to @#$^ me for a gasket? I didn't even think of that.

Also, I already got a regular output stator, however, the only accessory I have is a cd deck. You think I'll have a problem?
Reply With Quote
Sponsored Links
RhinoForums.net is the premier Yamaha Rhino UTV/ATV Forum on the internet. Registered Users do not see these ads. Please Register - It's Free!
  #17 (permalink)  
Old 11-01-2011, 02:30 PM
Member
 
My Rhino: 2009 450/2004 660
Join Date: Sep 2011
Location: Van Buren Ar.
Posts: 14
View mifrank67's Photo Gallery(0)
Just Google Rhino stator install and you will get a few step by step instructions, I used the Hunterworks one , and it helped alot except i took the gas tank out and the dont it gives you alot more room.
Reply With Quote
  #18 (permalink)  
Old 11-02-2011, 06:59 AM
erniejoe1's Avatar
Member
 
First Name: Ernie
My Rhino: 06 660
Join Date: Oct 2011
Location: SoCal
Posts: 109
View erniejoe1's Photo Gallery(0)
So far I have 4 vision x HIDs the 50 watters, in the middle of installing dome, rear amber and whip. I plan on installing an intercom/cb also

The gasket is about 10. plus shipping if you have it delivered.

Hunterworks is the one I used, worked very well follow step by step you can't go wrong.
Reply With Quote
  #19 (permalink)  
Old 11-02-2011, 07:50 AM
erniejoe1's Avatar
Member
 
First Name: Ernie
My Rhino: 06 660
Join Date: Oct 2011
Location: SoCal
Posts: 109
View erniejoe1's Photo Gallery(0)
I've heard that its a hit and miss with HO stators, hopefully they've had time to iron out the problems.
I forgot to mention that I did upgrade my battery to a PC925 it does fit in the tray youll need to shim the one side or the other because its not as wide as the stock one.
I'm going to R&D the stator this weekend.
Reply With Quote
  #20 (permalink)  
Old 11-02-2011, 07:54 AM
erniejoe1's Avatar
Member
 
First Name: Ernie
My Rhino: 06 660
Join Date: Oct 2011
Location: SoCal
Posts: 109
View erniejoe1's Photo Gallery(0)
I will be monitoring the charge with a lunar autometer voltage gauge.
Reply With Quote
  #21 (permalink)  
Old 11-07-2011, 09:51 AM
erniejoe1's Avatar
Member
 
First Name: Ernie
My Rhino: 06 660
Join Date: Oct 2011
Location: SoCal
Posts: 109
View erniejoe1's Photo Gallery(0)
Made it back from my trip and was pleasantly surprised.
I did notice a powerloss not much but I felt it.
Running all accessories which include 4 50 watt hids + 2 piaa 55 watt and driving lights my voltage gauge was right at 13volts. If you turn the driving lights and the 2 55 watt piaas off im at 13.5.
Im thinking my 4 50 watt hids were way over kill, I mean the guys back at camp seen me adjusting my lights on the mountain about 2 miles from camp...lol
Reply With Quote
  #22 (permalink)  
Old 11-07-2011, 10:23 AM
Member
 
First Name: Robbie
My Rhino: 2005 / 660 Rhino
Join Date: May 2011
Location: Phoenix
Posts: 18
View rjjencke's Photo Gallery(0)
Hahaha, that could be a bit overkill! At least you had no issues.

I finally pulled my stator using the Hunterworks guide. One of the coils looks like it was burnt/fried to hell.

Just got the gasket and had to razor off all the remains from the old one. Should be back together tonight then I'll check the voltage.

Question: I have never changed the oil yet, what do you guys use? Any issues with synthetic or should I go with Yamaha's stuff?
Reply With Quote
  #23 (permalink)  
Old 11-07-2011, 10:57 AM
erniejoe1's Avatar
Member
 
First Name: Ernie
My Rhino: 06 660
Join Date: Oct 2011
Location: SoCal
Posts: 109
View erniejoe1's Photo Gallery(0)
A bit overkill was right...lol

I stuck with the yamalube, reason is yamaha tests are very extensive and the money they spend in R&D is unbelievable, not saying that its the best but i belive for their equipment it probably is.
Reply With Quote
  #24 (permalink)  
Old 11-09-2011, 12:06 PM
Member
 
First Name: Robbie
My Rhino: 2005 / 660 Rhino
Join Date: May 2011
Location: Phoenix
Posts: 18
View rjjencke's Photo Gallery(0)
Went with Yamalube, all back together and running.

Tested each leg on the stator and I'm getting 15-17 volts for each combo.

With stator unplugged, I'm getting 13.10 V at the battery.

(I put dielectric grease in both plugs).

With the stator plugged in, I'm getting 13.81 V at the battery.

Do these numbers sound right for a standard output stator? Cause I'm ready for a hunt.
Reply With Quote
  #25 (permalink)  
Old 11-10-2011, 10:26 PM
Member
 
First Name: Robbie
My Rhino: 2005 / 660 Rhino
Join Date: May 2011
Location: Phoenix
Posts: 18
View rjjencke's Photo Gallery(0)
Actually, after trickle charging the battery I'm getting 13.8 Rhino off, and 14.5 Rhino idling. Not much difference with headlights or stereo on.
Reply With Quote
  #26 (permalink)  
Old 11-11-2011, 06:38 AM
erniejoe1's Avatar
Member
 
First Name: Ernie
My Rhino: 06 660
Join Date: Oct 2011
Location: SoCal
Posts: 109
View erniejoe1's Photo Gallery(0)
Great! Looks like your up and running.

Lets go kill something!
__________________
JBS Hot Rod Sheave, MSD, Fabtech, Fox, F1 Engineering, H.O. stator, Vision X HIDs, piaa
Reply With Quote
Reply

Lower Navigation
Go Back   Yamaha Rhino Forum - Rhino Forums.net > General Rhino > How-To


Search tags for this page
2005 grizzly 660 voltage regulator location
,

change stator on 660 rhino

,
how many poel on yamaha rhino stator
,
how many volts should a stator on a raptor put out
,
how to change a rhino 660 stator
,
how to check stator output on rhino
,
how to i know if stator is bad on rhino
,
how to pin out a 660 grizzly rectifier
,
how to replace stator on 660 rhino
,
rhino 660 stator
,

stator test on yamaha rhino 660

,
whete is voltage regulator on yamaa rhino
,
yamaha grizzly 660 stator resistance
,

yamaha rhino stator test

,

yamaha rhino voltage regulator test

Click on a term to search our sites for related topics.

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 11:24 PM.


RhinoForums.net is not associated with Yamaha in any way. We are an enthusiast site dedicated to the Yamaha Rhino. Our goal is to offer a place for Yamaha Rhino owners to discuss rides, events, mods, maintenance, purchasing, etc and offer help and assistance.