Yamaha Rhino Forum

Changing One Way Bearing

This is a discussion on Changing One Way Bearing within the Engine forums, part of the Technical category; my rhino started to free wheel this weekend so from what ive gathered on here its the one way bearing going bad. is this something ...


Go Back   Yamaha Rhino Forum - Rhino Forums.net > Technical > Engine

Engine For discussion of engine performance, and maintenance

Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 06-07-2011, 02:37 PM
moto92's Avatar
Senior Member
 
First Name: Chad
My Rhino: 2006 660 SE
Join Date: Jul 2008
Location: Mt. Vernon, IL
Posts: 1,027
View moto92's Photo Gallery(11)
Changing One Way Bearing

my rhino started to free wheel this weekend so from what ive gathered on here its the one way bearing going bad.
is this something i can do myself at home or are there any special tools required? ive done my own clutch kit so im familiar with all that, but havent been as far as the bearing.
also is there anything else in there that need should be replaced at this time? from looking at the parts i see there is one gasket that would probably have to be replaced but would that be it?
Reply With Quote
Sponsored Links
RhinoForums.net is the premier Yamaha Rhino UTV/ATV Forum on the internet. Registered Users do not see these ads. Please Register - It's Free!
  #2 (permalink)  
Old 06-07-2011, 03:46 PM
Roo's Avatar
Roo Roo is offline
Senior Member
 
First Name: Steve
My Rhino: 08' 700 FI
Join Date: Aug 2008
Location: So Cal
Posts: 1,641
View Roo's Photo Gallery(3)
Quote: Originally Posted by moto92 View Post
my rhino started to free wheel this weekend so from what ive gathered on here its the one way bearing going bad.
is this something i can do myself at home or are there any special tools required? ive done my own clutch kit so im familiar with all that, but havent been as far as the bearing.
also is there anything else in there that need should be replaced at this time? from looking at the parts i see there is one gasket that would probably have to be replaced but would that be it?

Yes, that's it. When you install the one way bearing in the clutch bell, be sure you cannot see the writing ( this side out ), and you might want to change the oil at the same time.
__________________
Muzzy exhaust
Stage 2 HC
K&N Intake system
JBS sheave, 16gr. OD weight, and sliders
MSD Charge FI prototype (3D mapping)
Alba Racing dyno tuned
TCP oil cooler relocation kit
Reply With Quote
  #3 (permalink)  
Old 07-17-2011, 08:19 AM
craka's Avatar
Rhino Rider
 
First Name: James
My Rhino: 2006 Rhino 660
Join Date: Oct 2009
Location: Middle Georgia
Posts: 235
View craka's Photo Gallery(0)
moto, looks like we are in the same chapter of the rhino life cycle, always with in weeks of each other. did you ever change this? my rhino stopped engine breaking and making a weird noise this weekend.
__________________
2012 Polaris Ranger XP 800


Rest in Pieces

2006 Yamaha Rhino 660 SE
Reply With Quote
  #4 (permalink)  
Old 07-17-2011, 08:58 AM
s2k1's Avatar
Official Site Vendor
Premium Member
 
Join Date: Feb 2007
Posts: 1,722
View s2k1's Photo Gallery(0)
Quote: Originally Posted by Roo View Post
Quote: Originally Posted by moto92 View Post
my rhino started to free wheel this weekend so from what ive gathered on here its the one way bearing going bad.
is this something i can do myself at home or are there any special tools required? ive done my own clutch kit so im familiar with all that, but havent been as far as the bearing.
also is there anything else in there that need should be replaced at this time? from looking at the parts i see there is one gasket that would probably have to be replaced but would that be it?

Yes, that's it. When you install the one way bearing in the clutch bell, be sure you cannot see the writing ( this side out ), and you might want to change the oil at the same time.
Actually that's correct . If you can see the writing on the bearing in the clutch bell, it is installed backwards. The bearing should be installed on the shoulder of the wet clutch assy, in this position you should rea the words " out side ".
__________________
Chris@BenchmarkPerformance.us
Benchmark Performance
760-484-0986
Engine Specialists, Side x Side Parts & Accessories, Discount OEM Parts
Reply With Quote
  #5 (permalink)  
Old 07-17-2011, 09:01 AM
craka's Avatar
Rhino Rider
 
First Name: James
My Rhino: 2006 Rhino 660
Join Date: Oct 2009
Location: Middle Georgia
Posts: 235
View craka's Photo Gallery(0)
Any special tools needed to change it... or any other parts like gaskets other than the one way bearing itself?

Thanks
__________________
2012 Polaris Ranger XP 800


Rest in Pieces

2006 Yamaha Rhino 660 SE
Reply With Quote
  #6 (permalink)  
Old 07-19-2011, 04:08 PM
moto92's Avatar
Senior Member
 
First Name: Chad
My Rhino: 2006 660 SE
Join Date: Jul 2008
Location: Mt. Vernon, IL
Posts: 1,027
View moto92's Photo Gallery(11)
Quote: Originally Posted by craka View Post
moto, looks like we are in the same chapter of the rhino life cycle, always with in weeks of each other. did you ever change this? my rhino stopped engine breaking and making a weird noise this weekend.
you better hope your not following in my steps. ive not changed my bearing yet because i also seem to need a new wet clutch. so until i scrap up the $500 for that job the rhino is parked in the garage
Reply With Quote
  #7 (permalink)  
Old 07-19-2011, 06:54 PM
craka's Avatar
Rhino Rider
 
First Name: James
My Rhino: 2006 Rhino 660
Join Date: Oct 2009
Location: Middle Georgia
Posts: 235
View craka's Photo Gallery(0)
dude! dont scare me like that! mine is still running strong besides the free wheeling going down hill. what did yours do?
__________________
2012 Polaris Ranger XP 800


Rest in Pieces

2006 Yamaha Rhino 660 SE
Reply With Quote
  #8 (permalink)  
Old 09-19-2011, 03:03 PM
sls666's Avatar
Member
 
First Name: Shawn
My Rhino: 09 limited 700
Join Date: Apr 2010
Location: saskatchawan
Posts: 170
View sls666's Photo Gallery(0)
any pictures anyware to refrence just trying to get ready to rip mine apart for a one way
__________________
RAZRKILLR
Trinity sheave epi 18s w gold spring
K&N filter/dmc duels/MSD
2" rubberdown customs lift/sport piggybacks
108s/26"terra Crosses/212s/30"silverbacks
trekker 4000 winch
Reply With Quote
  #9 (permalink)  
Old 09-19-2011, 04:12 PM
Member
 
Join Date: Jun 2011
Location: Charleston, WV
Posts: 879
View scottwv's Photo Gallery(0)
Quote: Originally Posted by craka View Post
Any special tools needed to change it... or any other parts like gaskets other than the one way bearing itself?

Thanks
No special tools....get a gasket and an oil change kit though!
Reply With Quote
  #10 (permalink)  
Old 02-16-2015, 12:15 PM
Member
 
Join Date: Dec 2013
Posts: 8
View Unclebob9's Photo Gallery(0)
Quote: Originally Posted by craka View Post
dude! dont scare me like that! mine is still running strong besides the free wheeling going down hill. what did yours do?
There is a seller on EBAY that sells the OEM Clutch shoe Blocks for $95 a set. they are not hard to install on the existing plate. It is also a good time to add Slugs (weights) to the shoes. The slugs will extend the life of the clutch shoes and make them grab better.
From my research a OEM one way bearing is the better choice. You will need a gasket for re-assembly. The "one way clutch bearing installs with the dot or writing facing out towards the left side of the rig and away from the center of the engine. The Belt installs with the arrows pointing towards the back of the Rhino.
A JBS sheave kit is also worth looking into.
An impact gun and a torque wrench will make the job easier.
Reply With Quote
  #11 (permalink)  
Old 02-16-2015, 01:42 PM
Member
 
Join Date: Dec 2012
Location: Nashville TN
Posts: 215
View jimclemjr's Photo Gallery(0)
Before you buy the clutch pads you should know that if the ebay guy has the OEM pads he is the only one. The factory dealers and online OEM suppliers only sell the whole clutch from all that I can find. The ebay guy has pads that WILL FIT the OEM clutch but I doubt they are OEM. Before you make a decision to but those make sure of what shape your clutch drum is in and then watch the video that JBS did of what the non-OEM pads leave behind. Then ask yourself if it's worth saving a $150? Also Clutch-wise make sure you are using the JASO rated oil required.
__________________
08 700 Black Armor SE, resi-shocks, 27" ITP Mudlite XTR, STI single Beadlock 14x7 wheels, stock running gear, 4point harnesses, Viper 4500 winch, Unleashed sheave, JBS 18 gr OD weights & purple spring(greased), Rigid Ind lights, Dual batteries with manual switch, chopped cage 6",
Reply With Quote
  #12 (permalink)  
Old 02-17-2015, 08:07 AM
Member
 
Join Date: Dec 2013
Posts: 8
View Unclebob9's Photo Gallery(0)
Quote: Originally Posted by jimclemjr View Post
Before you buy the clutch pads you should know that if the ebay guy has the OEM pads he is the only one. The factory dealers and online OEM suppliers only sell the whole clutch from all that I can find. The ebay guy has pads that WILL FIT the OEM clutch but I doubt they are OEM. Before you make a decision to but those make sure of what shape your clutch drum is in and then watch the video that JBS did of what the non-OEM pads leave behind. Then ask yourself if it's worth saving a $150? Also Clutch-wise make sure you are using the JASO rated oil required.
I talked to the guy at JW power parts (the Ebay seller) he assured me that the shoe blocks he sells are OEM. not after market. I found him on the Forum and he has a very good reputation. He also has a web-site where you can buy them directly from him for $5 less.
I have an original and a JW one in my hand right now and they are identical down to the numbers stamped on them. If they are copies, they did a good job and JW power parts lied to me. Otherwise they are OEM.
feel free to contact them yourself: JW PowerParts. Baton Rouge, LA Voice: 225-753-9455.
So it came down to saving $150 for 15 minutes of work removing the old shoes and installing the replacements on the OEM plate.
Reply With Quote
  #13 (permalink)  
Old 02-19-2015, 03:44 PM
Member
 
Join Date: Dec 2012
Location: Nashville TN
Posts: 215
View jimclemjr's Photo Gallery(0)
Unclebob-that's what I love about forums, appreciate the kickback, Ice storm killed my internet for a few days so sorry for delay in response. I have no issue for JW Powerparts. I looked at his site and to my eye and comparison there are some minor differences in the steel brackets but my big concern is the composition of the lining material. The lining is obviously going to wear and the residue that it produces and leaves in your engine concerns me. So just on risk for saving a $150 over several thousand miles, I do not think it worth it. It isn't about the extra maintenance either, I will save money on some aftermarket if there is no potential for long term risk. I buy the cheap brake pads and change them more frequently. All I was saying was it is strange that he claims to have OEM when even the dealers can't get it. You don't typically get premium material cheaper either. So that does not give me confidence that he has a premium lining that is inside my engine wearing away. If you watch this video link it helps establish my thinking on this matter and the extra caution that I was encouraging others in making their decision.
Reply With Quote
  #14 (permalink)  
Old 02-19-2015, 05:39 PM
Member
 
Join Date: Dec 2013
Posts: 8
View Unclebob9's Photo Gallery(0)
you are contradicting yourself.
First you say that you have no problem with JW powersports and then you call them a bunch of Liars for stating that their shoes are OEM?
You cannot have it both ways. Either they are flay out lying or they are OEM. Which are you saying?
Reply With Quote
  #15 (permalink)  
Old 02-19-2015, 06:30 PM
Member
 
Join Date: Dec 2012
Location: Nashville TN
Posts: 215
View jimclemjr's Photo Gallery(0)
Unclebob I am not going to get into a word match/debate. Obviously you have some strong feelings and as far as I know a friend of JW. I will retract the word 'problem' and substitute 'targeting' if you will be gracious enough to allow that. I am not targeting anyone - In the spirit of sharing knowledge on the forum I contributed that I could not find them anywhere else. You are free to infer whatever you want but I never accused anyone of being 'a bunch of liars'. It is so unique that 'I doubt it'. Just my opinion. If I did not feel that this material inside our engines was critical, I probably would have remained silent. I have no profit to make in this deal or personal alliances. Just a fact shared so that others could make an informed decision. And I recognize that I am not the end all of all facts so I listened to your fact of what the seller told you. And I will believe that you reported accurately-thanks.
__________________
08 700 Black Armor SE, resi-shocks, 27" ITP Mudlite XTR, STI single Beadlock 14x7 wheels, stock running gear, 4point harnesses, Viper 4500 winch, Unleashed sheave, JBS 18 gr OD weights & purple spring(greased), Rigid Ind lights, Dual batteries with manual switch, chopped cage 6",
Reply With Quote
Reply

Lower Navigation
Go Back   Yamaha Rhino Forum - Rhino Forums.net > Technical > Engine
Remove Ads


Search tags for this page
2008 yamaha rhino one way bearing instalation
,
change one way starter clutch in a rhino
,
gasket for 2007 yamaha rhino starter bearing replacement
,
how to change oneway bearing 700 bennche
,
how to replace a one way bearing in 700 grizzly
,
one way bearing clutch 2006 yamaha rhino 660
,
picture of 700 rhino one way bearing
,
rhino 660 how to replace one way bearing
,
rhino hd one way bearing
,
rhino one way bearing
,
where is one way bearing on rhino 660
,
wow to reinstall starter cluctch on 660 rhino
,

yamaha rhino one way bearing

,

yamaha rhino one way bearing replacement

,
yamaha rhino one way clutch bearing replace
Click on a term to search our sites for related topics.

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 01:50 AM.


RhinoForums.net is not associated with Yamaha in any way. We are an enthusiast site dedicated to the Yamaha Rhino. Our goal is to offer a place for Yamaha Rhino owners to discuss rides, events, mods, maintenance, purchasing, etc and offer help and assistance.