Yamaha Rhino Forum

r1 wiring help

This is a discussion on r1 wiring help within the Engine Swap forums, part of the Technical category; Starting to wire my R1 today and wondering if anyone has any tips to make this a little easier? What plugs are necessary and what ...


Go Back   Yamaha Rhino Forum - Rhino Forums.net > Technical > Engine Swap

Engine Swap For discussion of engine swaps or anything pertaining to an engine that doesn't come stock on the Rhino!

Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 06-04-2011, 09:44 AM
tnez10's Avatar
Member
 
Join Date: Dec 2010
Posts: 59
View tnez10's Photo Gallery(0)
r1 wiring help

Starting to wire my R1 today and wondering if anyone has any tips to make this a little easier? What plugs are necessary and what should be bypassed? How big of a headache are these to wire up? Also has anyone used one of the Rossen Racing modified harnesses? Are they pretty much made where I can plug it in and go? I might consider that option if so.

Thanks

Last edited by tnez10; 06-04-2011 at 04:15 PM.
Reply With Quote
Sponsored Links
RhinoForums.net is the premier Yamaha Rhino UTV/ATV Forum on the internet. Registered Users do not see these ads. Please Register - It's Free!
  #2 (permalink)  
Old 06-13-2011, 11:19 AM
Member
 
First Name: Jonathan
My Rhino: Rhino 1000
Join Date: Apr 2011
Location: Gilbert, AZ
Posts: 84
View RhinoSV1000's Photo Gallery(0)
hey im doing an SV1000 swap right now and im having trouble with wiring. no fuel or spark. from what i researched alot of people are tieing together the clutch wire and sand stand switch. some are some bypassing the tip over sensor using a resistor. i think its a 60K or 120K something like that. hopefully that helps a little
Reply With Quote
  #3 (permalink)  
Old 06-13-2011, 11:46 AM
trunknuts's Avatar
Learning everyday.
 
My Rhino: 2007 Limited
Join Date: Jun 2008
Location: SoCal
Posts: 1,006
View trunknuts's Photo Gallery(0)
R1 Wiring

R1 wiring:
-Bypass kickstand
-Bypass Clutch lever wires
-Mount Exup module or purchase bypass module
-I'd recommend leaving the tip sensor on and make a bracket for it
-Need resistor to keep low fuel indicator from blinking
-Tie in switches for ACC and Start
-Make sure all grounds, including body grounds, are tied in together
-There are two wires that go to the main switch that need to be grounded. The schematic in the service manual does not make this obvious. I couldn't get my motor running until WyattEarp (member) told me this. Locate the Blue/Yellow and Blue/Black wires and ground them.


That's all I can remember right now. I'm sure I'm forgetting something.
Attached Thumbnails
r1 wiring help-r1-wiring.jpg  
Reply With Quote
  #4 (permalink)  
Old 06-13-2011, 11:52 AM
Member
 
First Name: Jonathan
My Rhino: Rhino 1000
Join Date: Apr 2011
Location: Gilbert, AZ
Posts: 84
View RhinoSV1000's Photo Gallery(0)
"Locate the Blue/Yellow and Blue/Black wires and ground them."

i will look at mine and make sure thats not messing me up. For your harness are those two wires on a plug that is near the main switch?? if those arnt grounded, do you still get the motor to turn over?
Reply With Quote
  #5 (permalink)  
Old 06-13-2011, 11:58 AM
trunknuts's Avatar
Learning everyday.
 
My Rhino: 2007 Limited
Join Date: Jun 2008
Location: SoCal
Posts: 1,006
View trunknuts's Photo Gallery(0)
My motor is a 2008. I don't have access to the Rhino this week so I cant check. But yes, the two wires are on the plug going to the main switch. If they are not grounded the engine will turn over, but it will not start. I was going crazy with this. If it wasn't for WyattEarp I would've torched the whole damn car!
Reply With Quote
  #6 (permalink)  
Old 06-13-2011, 12:04 PM
Member
 
First Name: Jonathan
My Rhino: Rhino 1000
Join Date: Apr 2011
Location: Gilbert, AZ
Posts: 84
View RhinoSV1000's Photo Gallery(0)
hhaha im about to throw something at it soon if i cant figure it out
mine looks like this

do i have the same 2 wires as you guys??
Attached Thumbnails
r1 wiring help-wire1.jpg  
Reply With Quote
  #7 (permalink)  
Old 06-13-2011, 12:11 PM
trunknuts's Avatar
Learning everyday.
 
My Rhino: 2007 Limited
Join Date: Jun 2008
Location: SoCal
Posts: 1,006
View trunknuts's Photo Gallery(0)
Do you have a link for the service manual you can post? Either that or do you have a picture of the entire wiring schematic? I've never messed with the SV1000, but I'd like to try and help.
Reply With Quote
  #8 (permalink)  
Old 06-13-2011, 12:17 PM
Member
 
First Name: Jonathan
My Rhino: Rhino 1000
Join Date: Apr 2011
Location: Gilbert, AZ
Posts: 84
View RhinoSV1000's Photo Gallery(0)
diagram

http://www.edubs.net/bikestuff/sv100...plementary.pdf

its on the last pages (SK5)

thanks for taking a look!
Reply With Quote
  #9 (permalink)  
Old 06-13-2011, 12:35 PM
WildEarp's Avatar
Senior Member
 
Join Date: May 2007
Posts: 1,819
View WildEarp's Photo Gallery(0)
I kept as much of the stock harness as I could (for now), and only bypassed the things I needed to (like trucknuts stated above). I was able to do it with very little work on the harness, except for extending the wires to the gauge cluster. Ive got the resistor info for the low fuel sensor if you need it (PM me).
__________________
Ben Haines
Reply With Quote
  #10 (permalink)  
Old 06-13-2011, 01:36 PM
trunknuts's Avatar
Learning everyday.
 
My Rhino: 2007 Limited
Join Date: Jun 2008
Location: SoCal
Posts: 1,006
View trunknuts's Photo Gallery(0)
Quote: Originally Posted by WildEarp View Post
I kept as much of the stock harness as I could (for now), and only bypassed the things I needed to (like trucknuts stated above). I was able to do it with very little work on the harness, except for extending the wires to the gauge cluster. Ive got the resistor info for the low fuel sensor if you need it (PM me).
Is this on the SV1000 or the R1?
Reply With Quote
  #11 (permalink)  
Old 06-13-2011, 01:55 PM
WildEarp's Avatar
Senior Member
 
Join Date: May 2007
Posts: 1,819
View WildEarp's Photo Gallery(0)
Quote: Originally Posted by trunknuts View Post
Quote: Originally Posted by WildEarp View Post
I kept as much of the stock harness as I could (for now), and only bypassed the things I needed to (like trucknuts stated above). I was able to do it with very little work on the harness, except for extending the wires to the gauge cluster. Ive got the resistor info for the low fuel sensor if you need it (PM me).
Is this on the SV1000 or the R1?
R1
__________________
Ben Haines
Reply With Quote
  #12 (permalink)  
Old 06-13-2011, 02:52 PM
WildEarp's Avatar
Senior Member
 
Join Date: May 2007
Posts: 1,819
View WildEarp's Photo Gallery(0)
The low fuel warning light can be bypassed by adding a 470 OHM 1/4 watt resistor inline with the wire coming from the gauges. On 03-06 this wire is Green with a white tracer.

GAUGES-------RESISTOR---------Ground

Just cut the wired somewhere down the line from the gauges, solder the resistor to the side going to gauges. Then solder a new wire to the other end of the resistor, and ground that wire. Tape off the unused end of the stock fuel level wire.
__________________
Ben Haines
Reply With Quote
  #13 (permalink)  
Old 06-13-2011, 09:58 PM
Member
 
First Name: Jonathan
My Rhino: Rhino 1000
Join Date: Apr 2011
Location: Gilbert, AZ
Posts: 84
View RhinoSV1000's Photo Gallery(0)
Okay so i tried putting it in dealer mode and it doesnt do anything. it still says CHEC. i tried it 3 times.

im using the stock ignition key and im getting 9V to the ECM. Still got nothing

i tried bypassing the tip over sensor with a resistor and still nothing.

i check to the fuel pump to see if the ECM was sending volts to it, 0.0V, nothing

double checked all grounds, nothing!

replace the two 30A started fuses and 15A ignition fuse, nothing!!

disconnected the gauge cluster, nothing!!!

grabbed my cell phone and threw it at the rhino, Nothing!!!!!! jk

when i say nothing i mean, no spark and no fuel, but its still rolling over.

starter relay does not click when i turn the key also, it should right??

would a faulty starter relay cause a no spark or fuel but still let the motor turn over???

i am beginning to think its the ECM.....crap
Reply With Quote
  #14 (permalink)  
Old 06-13-2011, 10:10 PM
trunknuts's Avatar
Learning everyday.
 
My Rhino: 2007 Limited
Join Date: Jun 2008
Location: SoCal
Posts: 1,006
View trunknuts's Photo Gallery(0)
9 volts to the ECM? Shouldn't it be 12 volts?
Reply With Quote
  #15 (permalink)  
Old 06-13-2011, 10:27 PM
Member
 
First Name: Jonathan
My Rhino: Rhino 1000
Join Date: Apr 2011
Location: Gilbert, AZ
Posts: 84
View RhinoSV1000's Photo Gallery(0)
the ignition has a diode/resister in it so that you can not hot wire it by just connecting all 4 wires. MX_racer is doing the same swap and he had to run a resistor since he does not have the oem ignition key switch. nothing will trigger if the ecm sees 12v on start up.
Reply With Quote
Reply

Lower Navigation
Go Back   Yamaha Rhino Forum - Rhino Forums.net > Technical > Engine Swap


Search tags for this page
02 r1 main switch wiring
,

2002 yamaha r1 hot wired

,
2002 yamaha r1 wire harness gauge color codes in plug
,

dwarf car wiring resistor

,
hotwire r1 bike
,

how to hot wire a r1 ignition

,
how to hot wire r1
,
how to hotwire a 03 yamaha r1
,

how to hotwire a yamaha r1

,
how to hotwire r1
,

how to hotwire yamaha r1

,
how to wire rhino for r1 engine
,
were is ignition wiring 06 r1
,
what do i need to build a wireing harness for a 2002 yamaha r1
,
what wire do i use to hotwire a yamaha r1
Click on a term to search our sites for related topics.

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 12:50 AM.


RhinoForums.net is not associated with Yamaha in any way. We are an enthusiast site dedicated to the Yamaha Rhino. Our goal is to offer a place for Yamaha Rhino owners to discuss rides, events, mods, maintenance, purchasing, etc and offer help and assistance.