2008 700 Stator Test Results - Yamaha Rhino Forum - Rhino Forums.net
Yamaha Rhino Forum

2008 700 Stator Test Results

This is a discussion on 2008 700 Stator Test Results within the Audio, Lighting and Electrical forums, part of the Technical category; These are the test results of my stator. Please let me know if you think it's ok or bad. These are across each of the ...


Go Back   Yamaha Rhino Forum - Rhino Forums.net > Technical > Audio, Lighting and Electrical

Audio, Lighting and Electrical For discussion of lighting, stereo, and other electrical components

Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 06-08-2011, 08:34 AM
Member
 
My Rhino: 2008 Camo 700
Join Date: Jun 2011
Location: kentucky
Posts: 4
View BobbyScottJr's Photo Gallery(0)
2008 700 Stator Test Results

These are the test results of my stator. Please let me know if you think it's ok or bad. These are across each of the three wires.


200 ohm test, 1-2=.7 1-3=.7 2-3=.7

AC ouput Low idle, 1-2=19.5V 1-3=2.3V 2-3=21V
AC output high idle, 1-2=41V 1-3=2.1V 2-3=41V
Reply With Quote
Sponsored Links
RhinoForums.net is the premier Yamaha Rhino UTV/ATV Forum on the internet. Registered Users do not see these ads. Please Register - It's Free!
  #2 (permalink)  
Old 06-08-2011, 03:16 PM
benzo's Avatar
Legendary
 
My Rhino: 2006 rhino 660
Join Date: Mar 2010
Location: Phx,AZ
Posts: 5,813
View benzo's Photo Gallery(0)
did u not see the link i sent u in ur other thread u started last night ?

http://www.rhinoforums.net/lighting-...tml#post548492
Reply With Quote
  #3 (permalink)  
Old 06-08-2011, 04:44 PM
1bddelx's Avatar
Supernova
 
First Name: Jeff
My Rhino: 2008 SE
Join Date: Sep 2008
Location: So. Cal
Posts: 2,634
View 1bddelx's Photo Gallery(9)
This is all I could find

AC magneto
Model/manufacturer F004T39372/MITSUBISHI ----
Standard output 14.0 V 33.5 A at 5,000 r/min ----
Stator coil resistance/color 0.099 ~ 0.121 Ω at 20 C (68 F)/
white-white
----
Rectifier/regulator
Type Semiconductor-short-circuit ----
Model/manufacturer FH012AA/SHINDENGEN ----
No load regulated voltage (DC) 14.2 ~ 14.8 V ----
Rectifier capacity 50.0 A ----
Withstand voltage 40.0 V ----
__________________


MMM


Slow as hell
Reply With Quote
  #4 (permalink)  
Old 06-08-2011, 07:22 PM
Premium Member
Premium Member
 
Join Date: Jan 2007
Posts: 3,369
View SteveS's Photo Gallery(0)
Quote: Originally Posted by BobbyScottJr View Post
These are the test results of my stator. Please let me know if you think it's ok or bad. These are across each of the three wires.


200 ohm test, 1-2=.7 1-3=.7 2-3=.7

AC ouput Low idle, 1-2=19.5V 1-3=2.3V 2-3=21V
AC output high idle, 1-2=41V 1-3=2.1V 2-3=41V
Unless there is a mis-type there, your AC voltage measurements show a problem on the 2.3 measured volt output leg, as the other two legs are putting out 20'ish volts at low idle. Since the high idle voltages show the same sort of mismatch, I suspect that it is real. The 20-40 V AC readings look reasonable based on my memory, but the 2V measured leg is dead. It could conceivably be a bad electrical connection at an electrical connector in the circuit?

The resistance measurements are suspect, as it takes a special type of Ohm-meter to make accurate measurements at the sub-tenth ohm range. A 200 ohm range setting does not accurately measure at the last digit (1/10 ohm). If I recall correctly, the reistance is only a tenth or two tenths ohms (a dead short to an ordinary ohm-meter).

Oh, by the way; touch the ohm-meter probes together and you will see a few tenths ohm reading that bounces around a bit. That shows the error in the measurement at low resistance values...
__________________
2004 Rhino 660

Last edited by SteveS; 06-08-2011 at 07:30 PM.
Reply With Quote
  #5 (permalink)  
Old 06-09-2011, 03:55 AM
Member
 
My Rhino: 2008 Camo 700
Join Date: Jun 2011
Location: kentucky
Posts: 4
View BobbyScottJr's Photo Gallery(0)
Yes Benzo I seen your post and do thank you for the reply, I was only wanting to confirm these reading with everyone before I ordered the parts. It's hard to waste $300 bucks hoping that fixes it. The low reading on one leg isn't a mis type. So thanks for everyones help with this. I'll put a new stator in.
Reply With Quote
  #6 (permalink)  
Old 06-16-2011, 04:53 PM
Member
 
My Rhino: 2008 Camo 700
Join Date: Jun 2011
Location: kentucky
Posts: 4
View BobbyScottJr's Photo Gallery(0)
Put the new stator in today, everything working as it should. Hope it last longer than 2800 miles. Installed it myself, cost was right at $300 for everything.
Thanks again for all the help.
Reply With Quote
Reply

Lower Navigation
Go Back   Yamaha Rhino Forum - Rhino Forums.net > Technical > Audio, Lighting and Electrical


Search tags for this page
2008 rhino 700, stator test
,
2008 yamaha grizzly 700 regulator test
,
2008 yamaha rhino 700 stator
,
2008 yamaha rhino stator
,
grizzly 700 stator is reading 00.3 ohm
,
how much volts 2008 700 grizzly stator
,
how to check stator on 2008 grizzly
,
how to test a grizzly 700 stator
,
stater out put on rhine 700
,
stator coils for a 2008 yamaha 700 grizzly atv
,
yamaha grizzly 700 stator
,
yamaha rhino 700 stator install
,
yamaha rhino 700 stator test
,

yamaha rhino stator test

,
yamaha rhino stator voltage test
Click on a term to search our sites for related topics.

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 04:47 PM.




vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2016 DragonByte Technologies Ltd.
RhinoForums.net is not associated with Yamaha in any way. We are an enthusiast site dedicated to the Yamaha Rhino. Our goal is to offer a place for Yamaha Rhino owners to discuss rides, events, mods, maintenance, purchasing, etc and offer help and assistance.